consumerkrot.blogg.se - Cisco 2950 switch default ip

#CISCO 2950 SWITCH DEFAULT IP PASSWORD#
#CISCO 2950 SWITCH DEFAULT IP PC#
#CISCO 2950 SWITCH DEFAULT IP MAC#

Verify it has been created with the show vtp status command.

On switch1 and switch2, set up a VTP domain called ciscokits.

#CISCO 2950 SWITCH DEFAULT IP PC#

Because your router, PC and the switch-to-switch link are all in VLAN1, you should be able to ping between the PC2 and the router. You should note that, by default, all switch ports are in VLAN1.

On switch1 and switch2, issue the show vlan command.

Also, using the winipcfg utility, check that PC has a configured IP address of 197.10.1.2/24. If you cannot ping successfully, check that your router’s Ethernet0 IP address is 197.10.1Īnd that the interface is enabled.

Verify you can presently ping between the PC and your router.

On the PC using winipcfg, configure an IP address of 197.10.1.2/24 and a default gateway of 197.10.1.1.Switch1 and switch2 are interconnected through their fa0/12 Fast Ethernet ports. Your Router is connected to e0/1 on switch1 and the PC is connected to e0/1 on switch2. In this lab, you will set up VLANs on switch1 and switch2 (Catalyst 2950 switches) and test them by pinging between your router and PC.LAB VLANs and TRUNKING (Catalyst 2950 Switches)

#CISCO 2950 SWITCH DEFAULT IP MAC#

The switch will ‘sticky-learn’ the MAC address of the device connected to port fa0/9 and will only allow that device to connect to the port in the future.Ģ950sw2(config-if)# switchport port-securityĢ950sw2(config-if)# switchport port-security maximum 1 On switch2, configure port security for port fa0/9.

Issue the show mac-address-table command to verify the device is in the table as a permanent entry.Ģ950sw2(config)# mac-address-table static 4444-4444-4444 vlan 1 int fa0/5

On switch2, permanently assign a device with MAC address 4444-4444-4444 to port fa0/5.

This shows which devices are attached to which switch ports.

On switch2, issue the show mac-address-table command.

On switch4, issue the show spantree command.

On switch2, issue the show version command.

#CISCO 2950 SWITCH DEFAULT IP PASSWORD#

(the enable password should be encrypted when displaying the configuration file). Configure it with a hostname of 2950sw2 and an enable password of cisco HyperTerminal into Switch 2 (Catalyst 2950).On switch1, issue the show interfaces command.On switch1, issue the show interface vlan1 command to verify that the IP address, mask, and default gateway are correct.Reassign the switch a hostname of 2950sw1 and an enable pass of ‘cisco’ (unencrypted).Īssign the switch an IP address of 197.10.1.99 with a subnet mask of 255.255.255.0.Īssign the switch a default gateway of 197.10.1.1 (your router’s Ethernet address).Ģ950sw1(config-if)# ip address 197.10.1.99 255.255.255.0Ģ950sw1(config)# ip default-gateway 197.10.1.1 On 2950sw1, go into privileged mode and then into global configuration mode.On 2950sw1, erase the saved configuration and reload the switch.Display the saved configuration in NVRAMĢ950sw1# copy running-config startup-config On 2950sw1, type copy running-config startup-config to save the active configuration to NVRAM.On 2950sw1, type show running-config to see the active configuration.Then we will use exit or ctrl-z to get out of configuration mode. We will then assign Switch1 a host name of 2950sw1. On Switch1, we will go into privileged mode and then into global configuration mode.Type ? to see a list of privileged mode commands. Press the enter key to get into the user prompt mode. HyperTerminal into the switch you want to be Switch1.In this lab, you will configure basic IOS commands on Switch1 and Switch2 which are Catalyst 2950 switches.You will then connect Switch 1 and 2 together via port FA0/12 on each.

You will connectE0 on your Router to E0/1 on Switch1. Prerequisite Setup – You will configure an Ethernet router with an IP address of 197.10.1.1 255.255.255.0 to E0. As you progress through your CCNA exam studies, I am sure you will find that hands on experience you receive from such as lab will go a long way in helping you acheive your Cisco certification! So to assist you, below we provided one of our CCNA Labs, Cisco 2950 Switch VLAN & Trunking Lab. In preparation of your CCNA exam, we want to make sure we cover the various concepts that we could see on your Cisco CCNA exam.